RZ-G/RZ-G2L Flash Programming: Difference between revisions
Line 170: | Line 170: | ||
You want to use <code>sudo</code> because then all the files have root owner. | You want to use <code>sudo</code> because then all the files have root owner. | ||
cd temp | cd temp | ||
Assuming in the same folder | Assuming in the same folder the initrd script, as well as bl2 and fip (definitive version) are available: | ||
sudo cp ../my_init_flash_prog.sh home/root/ | sudo cp ../my_init_flash_prog.sh home/root/ | ||
Let's get | sudo cp ../bl2_bp.bin home/root/ | ||
sudo cp ../fip.bin home/root | |||
Let's get the initrd script executable: | |||
sudo chmod +x home/root/my_init_flash_prog.sh | sudo chmod +x home/root/my_init_flash_prog.sh | ||
We have to create a init symbolic link into the root folder: | We have to create a init symbolic link into the root folder: |
Revision as of 16:14, 8 March 2022
RZ/G2L boot modes and typical boot storage media
RZ/G2L boot modes are summarized in the table below.
MD_BOOT2 to MD_BOOT0 | Boot Mode | Interface Module | Connected Device | ||
0 | 0 | 0 | Boot mode 0 | SDHI0 | eSD (3.3 V at startup) |
0 | 0 | 1 | Boot mode 1 | SDHI0 | 1.8-V eMMC |
0 | 1 | 0 | Boot mode 2 | SDHI0 | 3.3-V eMMC |
0 | 1 | 1 | Boot mode 3 | SPIBSC | 1.8-V Single Quad or Octal serial flash memory |
1 | 0 | 0 | Boot mode 4 | SPIBSC | 3.3-V Single or Quad serial flash memory |
1 | 0 | 1 | Boot mode 5 | SCIF0 | Downloading through SCIF |
When the eMMC is delivered from the manufactures is normally divided into several areas as shown below.
In most of the Linux applications covered by the RZ/G2L, when it comes to non-volatile memory there are two main use cases:
- QSPI and eMMC. QSPI is normally used for firmware / boot loaders (i.e. ATF and u-boot) whereas eMMC for kernel and rootfs.
- eMMC only. In this case one of the two eMMC boot partitions is used for boot loaders and the user partition is then used for rootfs and kernel.
There might be other special cases but we can confidently state that these cover the great majority. We can also reasonably say that being the RZ/G2L a low-end device, there is the tendency to remove the QSPI to save money on the BOM.
At the end of the production line of course non-volatile memories are virgin (with a notable exception explained later) and need to be programmed. Usually firmware and bootloaders are relatively small (less than 1MB in total), kernel is instead in the tens of megabyte range and rootfs can go up to several hundreds of megabytes. To transfer this amount of data a fast interface is indeed required.
Flash Programming options
RZ/G2L cannot boot from USB, so at the end-of-line there are a few real viable options:
- Boot from SCIF (UART)
- Use JTAG
- It is worth to mention that, in general, if a QSPI FLASH is present on the custom board, it can also be bought preprogrammed
- Use a temporary QSPI flash card
In any of the cases above the goal is to have U-Boot up and running, then there are plenty of options to program the rootfs: ethernet, USB as host, USB with Mass Storage gadget, fastboot or even boot Linux kernel + initramfs.
With option 1, you can download Flash Writer and program the bootloaders, Arm Trusted Firmware (ATF) and U-Boot, into QSPI / eMMC boot partition, then reset and run U-Boot.
With option 2, you can download ATF and U-Boot via JTAG and then run the boot loaders without having to initially program them. Once U-Boot runs, you can program both bootloaders and rootfs.
With option 3, QSPI has already bootloaders pre-programmed, so U-Boot is already available.
With option 4, a QSPI flash card is somehow attached to the board that needs to be programmed. The QSPI flash contains ATF and U-Boot and potentially also the root file system to be programmed, depending on the size of both. More details are available here.
Unattended Flash Programming
All the options above may not require any human intervention and can be to a certain extent automatized.
In the rest of this page follow some examples on how to implement a fully atomized flash programming. More in particular we will focus on option 1, where:
- ATF and U-Boot are programmed using the SCIF.
- At the reboot U-Boot loads and boots kernel and the initramfs from USB.
- Then a custom init script is used of program the root file system stored on the USB thumb to the eMMC.
- After eMMC programming U-Boot is replaced, mainly to have a new set of environment variables to boot the final kernel / rootfs.
It is assumed that all binaries to be programmed are already available, for example as result of the porting of the BSP. This is the list of items that are needed:
- ATF BL2 and FIP binaries (e.g.
bl2_bp.bin
,fip.bin
); - Kernel image and device tree (e.g.
Image
,r9a07g044l2-smarc-smarc-rzg2l.dtb
); - Root file system image (e.g
sd_card.img.gz
) that can be easily created using this script.
However, there are other things to be done beforehand: step 0.
Step 0 - Environment set-up
Temporary u-boot
u-boot used at the first step is not the definitive one, its default environment parameters are adapted to allow the next steps to be executed automatically. The default environment parameters are configured in include/configs/BOARD_NAME.h
, for example for the RZ/G2L smarc board:
#define CONFIG_EXTRA_ENV_SETTINGS \ "bootm_size=0x10000000 \0" \ "baudrate=115200 \0" \ "bootargs=rw rootwait earlycon root=/dev/ram0 rdinit=/home/root/my_init_flash_prog.sh \0" \ "bootdelay=3 \0" \ "bootimagerd=booti 0x40180000 0x49000000 0x40100000 \0" \ "produsbbootargs=setenv bootargs rw rootwait earlycon root=/dev/ram0 rdinit=/home/root/my_init_flash_prog.sh \0" \ "usbload=usb start;fatload usb 0 0x40180000 Image;fatload usb 0 0x40100000 r9a07g044l2-smarc-smarc-rzg2l.dtb;fatload usb 0 0x49000000 core-image-minimal-smarc-rzg2l-mod.cpio.gz.u-boot;run produsbbootargs \0" #define CONFIG_BOOTCOMMAND "run usbload;run bootimagerd"
These parameters ensure that:
- After a boot delay of 3 seconds the command
usbload
is executed; usbload
, as the name suggests, after having initialized USB, loads kernel, device tree and initramfs into DDR.- boots kernel with initramfs and a custom init script that is in charge of programming kernel, device tree and the definitive root fs into eMMC.
It is important to note that u-boot has to be built with USB support, obviously. It may not be enabled by default, refer to this TBD page for more details.
Initrd script
This is the script that is going to be executed right after the kernel has finished booting.
#!/bin/bash DISK=/dev/mmcblk0 USB_DRIVE=/dev/sda1 FILE_NAME=sd_card.img.gz BL2=/home/root/bl2_bp.bin FIP=/home/root/fip.bin mount -t proc proc /proc mount -t sysfs sysfs /sys mount -t devtmpfs none /dev echo -e "\n== Destroying Master Boot Record (sector 0) ==" sleep 1 echo dd if=/dev/zero of=${DISK} bs=512 count=1 dd if=/dev/zero of=${DISK} bs=512 count=1 sync mount ${USB_DRIVE} /mnt echo "Programming eMMC, it should take 3-5 minutes please wait..." #</mnt/${FILE_NAME} gunzip >${DISK} dd if=/mnt/${FILE_NAME} | gzip -dc | dd of=${DISK} bs=1M status=progress sync echo "Enlarging ext partition to fit the eMMC size..." echo ", +" | sfdisk -N 2 ${DISK} resize2fs "${DISK}p2" echo "Reprogramming BL2 and FIP" echo "onto eMMC boot partition 0..." echo 0 > /sys/block/mmcblk0boot0/force_ro # disable the soft write-protect base dd if=${BL2} of=/dev/mmcblk0boot0 bs=512 skip=0 seek=1 dd if=${FIP} of=/dev/mmcblk0boot0 bs=512 skip=0 seek=256 echo "... and QSPI" dd if=/dev/zero of=boot.img bs=1024 count=1024 dd if=${BL2} of=boot.img conv=notrunc dd if=${FIP} of=boot.img conv=notrunc bs=512 seek=233 flashcp -v boot.img /dev/mtd0 echo "Done" echo "Wait 5s before reboot" sleep 5 reboot -f
Initramfs creation
Any root file system, including the final one that was created for the final application can be turned into a initramfs. However you have to take in account that it is convenient to have a small one. First it is loaded quicker from the thumb drive, then it has to be small enough to comfortably fit into the DRAM. In this example the initial rootfs is created using Yocto: bitbake core-image-minimal
. You may want to add packages like mtd-utils
and mmc-utils
that are useful to program QSPI and eMMC.
Once the minimal rootfs has been created, we have to modify it to add the custom initrd script (see previous section). In general, assuming you have your rootfs in the usual tar.gz/bz2 format, first of all we have to untar/unzip it into a temp folder:
mkdir temp sudo tar -xvf core-image-minimal-smarc-rzg2l.tar.bz2 -C temp
You want to use sudo
because then all the files have root owner.
cd temp
Assuming in the same folder the initrd script, as well as bl2 and fip (definitive version) are available:
sudo cp ../my_init_flash_prog.sh home/root/ sudo cp ../bl2_bp.bin home/root/ sudo cp ../fip.bin home/root
Let's get the initrd script executable:
sudo chmod +x home/root/my_init_flash_prog.sh
We have to create a init symbolic link into the root folder:
sudo ln -s sbin/init init
Now we are ready to pack the modified files to cpio ‘newc’ format:
sudo find . | sudo cpio --create --format='newc' > ../core-image-minimal-smarc-rzg2l-mod.cpio
Gzip it:
gzip -v core-image-minimal-smarc-rzg2l-mod.cpio
Finally create a u-boot image:
mkimage -n "core-image-minimal-smarc-rzg2l-mod" -A arm64 -O linux -T ramdisk -C none -d core-image-minimal-smarc-rzg2l-mod.cpio.gz core-image-minimal-smarc-rzg2l-mod.cpio.gz.u-boot
If the last command fails, then you need to install u-boot tools. For example in Ubuntu:
sudo apt install u-boot-tools
USB thumb drive preparation
We can now prepare a thumb drive with the following content:
- Kernel and device tree (
Image
,r9a07g044l2-smarc-smarc-rzg2l.dtb
); - Root file system image (
sd_card.img.gz
); - Initram fs (
core-image-minimal-smarc-rzg2l-mod.cpio.gz.u-boot
)
Step 1 - Programming ATF and u-boot via SCIF
The main tool that can assist in performing external non-volatile memory (QSPI and eMMC) is Flash Writer. Depending on the host PC used, you can either use a bash script or a TeraTerm macro. In both cases you would need two files:
bl2.bin
fip.bin
The file names may vary a bit. These are either the output of Yocto or generated by combining ATF and U-Boot binaries. Actually the first one is generated by ATF directly whereas the second is the generated by the Firmware Image Package (FIP) utility by combining BL3x binaries (BL31 secure monitor, optionally BL32 OP-TEE and BL33 u-boot).
Linux script
A Linux bash script is available here. Please refer to the README for help on the usage.
Windows TeraTerm macro
Usually dealing with this type of devices a Linux host PC is normally available. However sometimes it might be convenient to have a quick way to program the bootloaders using Windows. Especially during production, a Windows PC may be more convenient than a Linux PC.
Instead of using an ad-hoc tool developed only for the RZ/G2L the idea is to use a generic terminal utility. Tera Term is an open source tool that has some nice scripting capabilities embedded: a Tera Term script is called MACRO. The developed macro "replaces" the user and provides inputs to Flash Writer, whose binary is also downloaded automatically. There are just a couple of parameters that you would need to change (open the macro with a standard txt editor), stuff like COM port or the name of the Flash Writer binary to be used and whether the target is QSPI or eMMC. The "UNATTENDED" parameter suppresses all the user interaction apart from errors.
It is assumed that MD_BOOTx pins are already configured for the final boot mode. However, if the target flash is virgin / erased, the boot mode selected fails over to SCIF download, allowing the Flash Writer bin to be downloaded.
When the procedure is complete, the system gets reset and the system boots using the newly programmed files.
Step 2
At this step there's not anything to do, just to check that what we've done at step 0 works consistently. If everything is ok the system goes thru the standard boot stages and u-boot load kernel and initrd from the USB thumb drive.
Step 3
At this stage the custom initrd script is executed, programming the rootfs onto the eMMC user area. Note that at the end of the copy the ext4 partition is resized to the max allowed by the eMMC. Again, we just need to check that everything is inline with expectations.
Step 4
The last step is needed to replace u-boot default environment variables to values that allow the final rootfs to be booted from eMMC. This is the version of u-boot that was created originally, anyway here below the environment variables you may want to use:
#define CONFIG_EXTRA_ENV_SETTINGS \ "bootm_size=0x10000000 \0" \ "prodsdbootargs=setenv bootargs rw rootwait earlycon root=/dev/mmcblk1p2 \0" \ "prodemmcbootargs=setenv bootargs rw rootwait earlycon root=/dev/mmcblk0p2 \0" \ "bootimage=booti 0x40180000 - 0x40100000 \0" \ "emmcload=fatload mmc 0:1 0x40180000 Image;fatload mmc 0:1 0x40100000 r9a07g044l2-smarc-smarc-rzg2l.dtb;run prodemmcbootargs \0" \ "sd1load=fatload mmc 1:1 0x40180000 Image;fatload mmc 1:1 0x40100000 r9a07g044l2-smarc-smarc-rzg2l.dtb;run prodsdbootargs \0" \ "bootcmd_check=if mmc dev 1; then run sd1load; else run emmcload; fi \0" #define CONFIG_BOOTCOMMAND "env default -a;run bootcmd_check;run bootimage"
Use JTAG
TBD