RZ-G/RZ-G2L SMARC: Difference between revisions
No edit summary |
No edit summary |
||
Line 11: | Line 11: | ||
== RZ/G2L Evaluation Board Kit Configuration == | == RZ/G2L Evaluation Board Kit Configuration == | ||
[[File:board_configuration.png| | [[File:board_configuration.png|frameless]] | ||
== RZ/G2L SMARC Module Board (TOP) == | |||
[[File:smarc_module_board_top.png|frameless|]] | |||
== RZ/G2L SMARC Module Board (Bottom) == | |||
[[File:smarc_module_board_bottom.png|frameless|]] | |||
== RZ SMARC Series Carrier Board == | |||
[[File:smarc_series_carrier_board.png|frameless|]] | |||
== Power Supply == | |||
The following power supply environment is used in the evaluation of Renesas:<br> | |||
* USB Type-C cable CB-CD23BK (manufactured by Aukey) | |||
* USB PD Charger Anker PowerPort III 65W Pod (manufactured by Anker) | |||
[[File:power_supply.png|frameless|]] | |||
== Power ON == | |||
* Connect USB-PD Power Charger to USB Type-C Connector. Then LED1(VBUS PWR On) and LED3(Module PWR On) lights up. | |||
* Press SW9 to turn on the power. Then LED4(Carrier PWR On) lights up. | |||
[[File:power_on.png|frameless|]] | |||
== JTAG Cable Connection for ICE Debugging == | |||
* When connecting JTAG debugger, Please set the DIP SW1 settings as follows. JTAG connector is 10pin. | |||
[[File:JTAG_connection_ice_debug.png|frameless|]] | |||
== How to Set Boot Mode == | |||
[[File:boot_mode.png|frameless|]] | |||
== Debug Serial (Console Output) == | |||
* Debug serial uses CN14. The baud rate is 115200bps. | |||
[[File:debug_serial.png|frameless|]] | |||
* Since the serial-USB conversion IC is not always powered, the Windows PC will recognize it after the power switch is turned on. | |||
* If it is not recognized by your Windows PC, please install the driver�https://www.ftdichip.com/Drivers/VCP.htm |
Revision as of 18:17, 29 April 2021
← RZ-G
General Information
- Renesas RZ/G2L (R9A07G044)
- Official website
Board Documentation
RZ/G2L Evaluation Board Kit Configuration
RZ/G2L SMARC Module Board (TOP)
RZ/G2L SMARC Module Board (Bottom)
RZ SMARC Series Carrier Board
Power Supply
The following power supply environment is used in the evaluation of Renesas:
- USB Type-C cable CB-CD23BK (manufactured by Aukey)
- USB PD Charger Anker PowerPort III 65W Pod (manufactured by Anker)
Power ON
- Connect USB-PD Power Charger to USB Type-C Connector. Then LED1(VBUS PWR On) and LED3(Module PWR On) lights up.
- Press SW9 to turn on the power. Then LED4(Carrier PWR On) lights up.
JTAG Cable Connection for ICE Debugging
- When connecting JTAG debugger, Please set the DIP SW1 settings as follows. JTAG connector is 10pin.
How to Set Boot Mode
Debug Serial (Console Output)
- Debug serial uses CN14. The baud rate is 115200bps.
- Since the serial-USB conversion IC is not always powered, the Windows PC will recognize it after the power switch is turned on.
- If it is not recognized by your Windows PC, please install the driver�https://www.ftdichip.com/Drivers/VCP.htm